Tools Plumbers In Charlotte, NC Can’t Live Without
There are several reasons why you may need to call Plumbers In Charlotte, NC. They are the plumbing professionals to call when you have a clog; a backed up toilet, a leaky water heater, or a burst pipe. But they wouldn’t be able to do their job without the right tools. Most of the essential plumbing tools can be found in the toolbox. Just as with any job that you do, it is necessary to have the right tools for the job. Having the proper tools ensures that your plumber gets the job done right and with ease. If you were to peek into the toolbox of a AAA City Plumbing technician’s toolbox, you would most likely see most if not all of the following tools:
- Tongue-and-Groove Pliers
- Pipe Wrench
- Tubing Cutter
- Drill Machine
- The Basin Wrench
- Compression Sleeve Puller
One of the must-have plumbing tools is tongue-and-groove pliers. They are a universal tool that is used for many different jobs. They are also known as channel locks or water pump pliers. It has a long handle and is used to hold nuts, grabbing, twisting, pulling, or for loosening. A plumber will often have two. This is so they can use one to stabilize and the other for either loosening or tightening. The 10-inch size is a go-to size for most plumbers, but you may find a few different sizes in a plumber’s toolbox. Sometimes your plumber will wrap the pipe with some masking tape or a rag before using the pliers to prevent scratching the finish on the pipe.
A hacksaw is another essential tool for plumbers. It can be adjusted to fit different sizes of blades and can be used to cut a variety of different materials. It can cut even the strongest metal pipes and can handle pipes that a pipe cutter cannot.
The Pipe Wrench
The pipe wrench or plumber wrench has an adjustable spanner that can be easily adjusted to fit different sizes of pipes. It can be used to rotate pipes, and it’s not uncommon for your plumber to have two so that they can use one to fit a pipe while the other one holds the pipe. This type of pipe is commonly used to unscrew pressure regulators and heater nipples.
The Plumber’s Friend
This one may be obvious, but a plunger is one of the most basic tools a plumber can have. It is coined the “plumber’s friend” for a reason. A plunger is a suction cup on the end of a stick. It is commonly used to unclog toilets but is also effective in clearing blockages in drains and pipes. To use all you need to do is press it down until a tight seal is formed and then pull in an upward motion. The vacuum that is created will help to release any clogs.
There is a special type of plunger specifically designed for the tub or sink and is the same as a regular plunger. The main difference is that it does not have the same shape. A toilet plunger has a flange that will get a better seal in the bowl of a toilet. A flange plunger can be used in the sink, shower, or tub, but for hygienic reasons, it is just best to have a separate plunger for the toilet.
A tubing cutter, also known as a C-clamp tool, is used for cutting through pipes. A plumber will often have one that is specifically designed to cut through copper pipes and another for cutting through plastic pipes.
A drill machine can be used to make holes in metal and plastic pipes. They will normally be in a right angle drill style, and they come in handy because they can be used to reach tight areas, which makes it an ideal tool for pipe installation.
A hand auger, also known as the “plumber’s snake” is a hand-powered crank tool that has a long cable. As the stainless steel cable is cranked into a pipe, it will move farther as it clears the drain or pipe that it is fed it through. It can be very effective at unclogging tough clogs that a plunger will not fix.
Augers can be manually powered, connected to a drill, or even powered electrically. An auger can vary in length and size so a plumber may have a few different ones on hand. Closet augers are commonly used in the toilet because they have a “J” shape that is best suited to the shape of the trap under the toilet bowl. They also have a plastic cap that helps to protect the porcelain of the toilet bowl from getting damaged when used.
A drum auger is typically used to clean out bigger pipes such as the main drain line. They are usually powered by electricity, and they have blades attached to them so that they can effectively break up tougher clogs. Some drum augers even have cameras attached to the end to better access the clog.
The Basin Wrench
The basin wrench, also known as the sink wrench is a self-tightening wrench that is ideal for getting to hard-to-reach places. It will often have a telescoping shank that makes it easy to hold at a 90-degree angle. Many plumbers in Charlotte, NC use this tool.
Compression Sleeve Puller
A compression sleeve puller is what a plumber uses for working on PEX, copper, or CPVC tubing. It has the capability to remove the nit and compression sleeve without causing damage to the pipe.
There are also many other tools that a plumber will take with them on the job, such as an Allen wrench set, faucet packing, rubber washers, O-rings, and plumbers tape. Plumbers’ tape, also known as Teflon tape, is a thin, white tape that is used to thread around fittings and on the threads of pipes before twisting on parts together.
It helps to seal the joint and also acts as a lubricant for the threading process. Packing is a wax-coated string that is used to wrap around valve stems and can create a watertight seal. The rubber washers and O-rings in faucets eventually wear out and need to be replaced. They are available in variety packs so that your AAA City Plumbing technician can find the right size for your faucet. When equipped with the right equipment, there is nothing that your Plumbers In Charlotte, NC can’t do.
The information in the post came from the following sources: